das IF ist angeschraubt so wie in der anleitung. und ich weis einfach net weiter habe auch andere probs durchgelesen nur keiner kann helfen irgendwie
hier nen bootlog
beim booten
Code: Alles auswählen
Starting the automounter
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.9 2006/09/11 17:30:00 carjay Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of DBox2 IDE CPLD is at: 0xc38c4000
Probing IDE interface ide0...
hda: SAMQULG SP2514N, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Detected STB:
hda: attached ide-disk driver.
hda: host protected area => 1
Vendor: Nokia
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Code: Alles auswählen
hda: lost interrupt
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
hda: setmax_ext LBA 488528752, native 65924176
hda: 65924176 sectors (33753 MB) w/8192KiB Cache, CHS=4103/255/63
hda: lost interrupt
hda: set_multmode: status=0x53 { DriveReady SeekComplete Index Error }
hda: set_multmode: error=0x06 { DriveStatusError TrackZeroNotFound }
hda: lost interrupt
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
Partition check:
/dev/ide/host0/bus0/target0/lun0:[sectionsd] getUTC: read: Connection timed out
<3>hda: lost interrupt
hda: read_intr: status=0x51 { DriveReady SeekComplete Error }
hda: read_intr: error=0x04 { DriveStatusError }
hda: lost interrupt
hda: read_intr: status=0x51 { DriveReady SeekComplete Error }
hda: read_intr: error=0x04 { DriveStatusError }
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
hda: lost interrupt
hda: read_intr: status=0x51 { DriveReady SeekComplete Error }
hda: read_intr: error=0x04 { DriveStatusError }
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
hda: read_intr: status=0x51 { DriveReady SeekComplete Error }
hda: read_intr: error=0x04 { DriveStatusError }
ide0: reset: master: sector buffer error
hda: lost interrupt
hda: read_intr: status=0x51 { DriveReady SeekComplete Error }
hda: read_intr: error=0x04 { DriveStatusError }
hda: lost interrupt
hda: read_intr: status=0x51 { DriveReady SeekComplete Error }
hda: read_intr: error=0x04 { DriveStatusError }
hda: read_intr: error=0x04 { DriveStatusError }
ide0: reset: master: sector buffer error
end_request: I/O error, dev 03:00 (hda), sector 0
end_request: I/O error, dev 03:00 (hda), sector 2
end_request: I/O error, dev 03:00 (hda), sector 4
end_request: I/O error, dev 03:00 (hda), sector 6
end_request: I/O error, dev 03:00 (hda), sector 0
end_request: I/O error, dev 03:00 (hda), sector 2
end_request: I/O error, dev 03:00 (hda), sector 4
end_request: I/O error, dev 03:00 (hda), sector 6
unable to read partition table
Journalled Block Device driver loaded
mount: Mounting /dev/ide/host0/bus0/target0/lun0/part2 on /hdd failed: No such f
ile or directory
/dev/ide/host0/bus0/target0/lun0/disc:
setting standby to 60 (5 minutes)
end_request: I/O error, dev 03:00 (hda), sector 0
Code: Alles auswählen
msgbox Message-Box Version 1.52
umount: Couldn't umount /hdd: Invalid argument
end_request: I/O error, dev 03:00 (hda), sector 0
end_request: I/O error, dev 03:00 (hda), sector 2
end_request: I/O error, dev 03:00 (hda), sector 4
end_request: I/O error, dev 03:00 (hda), sector 6
Unable to read /dev/ide/host0/bus0/target0/lun0/disc
