seit einigen Tagen habe ich an meiner dbox2 den Effekt, dass zwei Streifen durch das Bild wandern. Diese sind mal größer, mal kleiner.
Leider kann ich mir absolut nicht erklären, woher diese auf einmal kommen. Um das Problem etwas einzugrenzen, habe ich sämtliche Stromverbraucher vom Netz getrennt – keine Besserung. Schaue ich TV direkt über Kabel (nicht mit der dbox), ist alles ok.
Unten habe ich das Bootlog beigefügt und ein Bild, wie das am TV ausschaut.
Ich wollte mich heute mal mit dem neuen Image Version 2.4.0 rc1 versuchen, da klappt allerdings der Downloadlink nicht.
Also, wenn mir jemand nen Tipp hat oder ein Hinweis, woher die Streifen kommen könnten, wäre ich sehr froh und dankbar.
Grüße Alex
Hier das LOG:
zapit shot down
Waiting for zapit (max. 5 seconds)
starting pid 224, tty '': '/etc/init.d/halt'
CXA2092 found
CXA2092 found
kill: you need to specify whom to kill
Unmounting 'xfs' on '/mnt/filme'
Unmounting 'xfs' on '/mnt/custom'
Unmounting 'xfs' on '/hdd'
Unmounting 'tmpfs' on '/tmp'
umount: can't umount /tmp: Device or resource busy
Unmounting 'jffs2' on '/var'
umount: can't forcibly umount /var: Device or resource busy
Oops: umount failed
-- trying to remount readonly...Ready to shutdown system...
The system is going down NOW!
Sent SIGTERM to all processes
[yhttpd] !!! SIGNAL !!! :15!
[yhttpd] No special SIGNAL-Handler:15!
[yhttpd] stop requested......
Sent SIGKILL to all processes
Requesting system rebootnfsd: last server has exited
nfsd: unexporting all filesystems
‘debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID dd gtxID 0b
debug: fpID 5a dsID 01-e1.b8.22.07.00.00-5f
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed
Flash-FS bootstrap loader (v1.5)
Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036
will verify ELF image, start= 0x800000, size= 170380
verify sig: 262
Branching to 0x40000
U-Boot 2009.08 (Tuxbox) (04.12.09 09:04:31)
CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: .. done.
env: found console with value ttyS0
env: found baudrate with value 9600
env: found dbox_duplex with value 1
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
env: found lcd_bias with value 0
FB: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
LCD: ready
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 671124 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
Image Name: Linux-2.4.37.7-dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 671060 Bytes = 655.3 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.37.7-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #1 Fr 4. Dez 08:
42:33 CET 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600
dbox_duplex=1
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
full-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:19:57:3c
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (squashfs+lzma)"
0x006a0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.15.2 (2009-12-04 09:15:43 CET)
starting pid 8, tty '': '/etc/init.d/rcS'
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: IDE-Interface detected, Vendor: Gurgel
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
dboxide: $Id: main.c,v 1.14 2009/06/19 14:39:26 seife Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of IDE-Interface is at: 0xc394f000
dboxide: IDE-Interface detected, Vendor: Gurgel
dboxide: sreset succeeded
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Probing IDE interface ide0...
hda: WDC WD5000AAJB-00UHA0, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 976773168 sectors (500108 MB) w/8192KiB Cache, CHS=60801/255/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
SGI XFS with no debug enabled
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
Adding Swap: 136544k swap-space (priority -1)
XFS mounting filesystem ide0(3,2)
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
XFS mounting filesystem ide0(3,3)
XFS mounting filesystem ide0(3,4)
/dev/ide/host0/bus0/target0/lun0/disc:
setting 32-bit IO_support flag to 1
setting drive write-caching to 1 (on)
setting standby to 120 (10 minutes)
IO_support = 1 (32-bit)
write-caching = 1 (on)
insmod: a module named xfs already exists
mount: mounting /dev/ide/host0/bus0/target1/lun0/part1 on /mnt/slave failed: No
such file or directory
/dev/ide/host0/bus0/target1/lun0/disc: No such file or directory
jtginfo $Id: jtginfo.c,v 2.2 2009/02/07 21:51:28 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
ves1x93: Detected ves1893a rev2
DVB: registering frontend 0:0 (VES1893)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Fri Dec 13 21:45:52 CET 1901
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
exportfs: /etc/exports [2]: Neither 'subtree_check' or 'no_subtree_check' specif
ied for export "*:/hdd".
Assuming default behaviour ('no_subtree_check').
NOTE: this default has changed since nfs-utils version 1.0.x
$Id: sectionsd.cpp,v 1.315 2009/11/30 21:50:26 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 24 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
15:45:07.013 [timeThread] Time set via NTP, going to sleep for 1800 seconds.
[timerd] woke up from timer? false!
15:45:08.023 dmxSDT: going to sleep...
[timerd] using config file /var/tuxbox/config/timerd.conf
$Id: zapit.cpp,v 1.450 2009/11/26 20:58:21 rhabarber1848 Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0 auto_fec 0
avia_gt_core: masking unhandled irq reg 0 bit 7
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 4 onid 85
[getservices] dup transponder id 1 onid 85
/var/tuxbox/config/zapit/ubouquets.xml: No such file or directory
/tmp/currentservices.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[camd] ca system id: 1702
[CVideo::setVideoFormat] output format: 4:3(LB)
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] found esound, adding personalized esound entry to mainmenue
[network config] Instance created
loading locales: scandir: No such file or directory
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=25 period=0 use kernel-repeat: no
[neutrino] registering as event client
[scan-setup] received 17 sats
index.xml: No such file or directory
[CVideo::setVideoFormat] output format: 4:3(LB)
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[zapit] tuned frequency does not match request. difference: 429
[camd] set emm caid 1702 capid 1000
SPTS, queue 0 extended.
[camd] starting onid 0001 sid 001b
[neutrino] no file /var/tuxbox/config/init.end was found
[camd] set emm caid 1702 capid 1000
[neutrino] initialized everything
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
15:45:41.459 eit_set_update_filter, servicekey = 0x10085001b, current version 14
descramble onid: 0001 sid: 001b status: 1d1d
nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/l
iblcddisplay.so.0)
[controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3)
TuxTxt running thread...(020)
TuxTxt service started 20
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
Hier das Bild vom TV:
