Kabelbox gibt sich als SAT Box aus; Hardwarefehler?

Hard- und Software Fragen rund um die dbox2 - außer zu, JtG-Team-Image
Antworten
Nachricht
Autor
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

Kabelbox gibt sich als SAT Box aus; Hardwarefehler?

#1 Beitrag von tklcb » So 06 Jan 2008, 16:02

Hallo,

in der Hoffnung hier an der richtigen Stelle zu sein:

Meine D-Box 2 von Nokia, 2xI ist der Meinung, eine Sat Box zu sein, ist sie aber in Wirklichkeit nicht (ist eine Kabelbox), weiter unten habe ich mal das aktuelle Log eingestellt, dort sind drei Passagen herausgestellt. Ich denke, das ein Harwaredefekt vorliegt, weiß nur nicht so recht, an welcher Stelle oder bei welchem Bauteil. Vielleicht kann mir von Euch jemand die Fehlerstelle etwas eingrenzen, dafür im Voraus vielen Dank!!!

das Log war leider zu lang für den D-Box Bootmanager, so dass der Anfang fehlt:

zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30780k available (1180k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1b:7d:5e
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (SquashFS)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.8.2 (2007-12-21 09:55:47 CET)
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
Machine check in kernel mode.
Caused by (from SRR1=9032): Transfer error ack signal
Oops: machine check, sig: 7
NIP: C38F68D8 XER: 20000000 LR: C38F6B1C SP: C1A5DD90 REGS: c1a5dce0 TRAP: 0200
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c1a5c000[74] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C38F6B1C C1A5DD90 C1A5C000 00000080 00000000 C38FE000 C1D2DD0C FDFFE000
GPR08: C1D2DD20 C38FE000 00000000 00000000 48008024 10074260 10050000 00000001
GPR16: 10070000 10077868 1006FD79 10077520 00009032 C1A5DEA0 C1A3C000 C3900000
GPR24: C1D2DCC0 00000007 C38FC000 C01465C4 FFFFFFEA 00000000 C0150000 C38F6000
Call backtrace:
C38F6B1C C38F8964 C00110D4 C000285C 100098E8 10003C68 10003C98
10003E58 0FEB15EC 00000000
Bus error
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode vB107
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
jtginfo $Id: jtginfo.c,v 1.9 2007/12/20 19:34:12 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Thu Jan 1 12:00:00 CET 1970
$Id: sectionsd.cpp,v 1.253 2007/12/02 14:46:36 seife Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
$Id: zapit.cpp,v 1.404 2007/12/17 09:53:04 seife Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
[frontend] uncommitted_switch_mode 0
avia_gt_core: masking unhandled irq reg 0 bit 7
/var/tuxbox/config/zapit/services.xml: No such file or directory
Machine check in kernel mode.
Caused by (from SRR1=1032): Transfer error ack signal
Oops: machine check, sig: 7
NIP: C38F6098 XER: 20000000 LR: C38F6088 SP: C1539E10 REGS: c1539d60 TRAP: 0200
Not tainted
MSR: 00001032 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c1538000[122] 'zapit' Last syscall: 54
last math 00000000 last altivec 00000000
GPR00: 00000000 C1539E10 C1538000 00000001 000000E0 20006F06 00000000 C3B8C9E8
GPR08: 0FD5E7F0 C38FE000 C3900000 C0004BE0 84002028 10037468 00000000 00000000
GPR16: 00000000 00000000 00000000 00000000 00009032 01539F40 C3B8C9E8 C15A46D0
GPR24: C155F400 00000001 00000000 00000000 000000E0 00000000 00000000 00000000
Call backtrace:
C003EDA4 C3B8CEC0 C38D24E8 C38CD380 C0043FEC C000285C 00000000
10014E58 10014F28 10010B04 10013190 0FC9B5EC 00000000
[camd] ca system id: 1722
$Id: controld.cpp,v 1.127 2007/07/01 08:40:13 dbluelle Exp $

[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
Machine check in kernel mode.
Caused by (from SRR1=1032): Transfer error ack signal
Oops: machine check, sig: 7
NIP: C38F6098 XER: 00000000 LR: C38F6088 SP: C1501DB0 REGS: c1501d00 TRAP: 0200
Not tainted
MSR: 00001032 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c1500000[129] 'controld' Last syscall: 54
last math 00000000 last altivec 00000000
GPR00: 00000000 C1501DB0 C1500000 00000001 000003B0 C1501E14 C1501E50 C3B8C35C
GPR08: 00000000 C38FE000 C3900000 C0004BE0 84002028 1002122C 00000000 00000000
GPR16: 00000000 00000000 00000000 00000000 00009032 01501F40 C3B8C35C C15A4D60
GPR24: C152ED20 00000002 00000000 C1501E14 000003B0 00000000 7FFFFD00 C1501E50
Call backtrace:
C1501DB4 C38F8750 C3B8C68C C38D25C8 C38CD380 C0043FEC C000285C
00000000 10006480 10006C50 10005F50 0FC475EC 00000000
[yhttpd] Webserver nhttpd/3.1.6 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[yhttpd] Webserver starting...
/bin/neutrino: /lib/libpng12.so.0: no version information available (required by
/bin/neutrino)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[neutrino] received 0 sats
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[neutrino] registering as event client
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
Nach oben
Benutzeravatar
Jeppdot
Streamsüchtling
Streamsüchtling
Beiträge: 1784
Registriert: Do 01 Jan 2004, 18:03
Kontaktdaten:
Kontaktdaten von Jeppdot

#2 Beitrag von Jeppdot » So 06 Jan 2008, 16:11

Hallo,

welches Image?

Code: Alles auswählen

[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)


Ist das der allererste Start der Box?
Was sagt JtG-Info zu der box?

Ach ja:
http://wiki.tuxbox.org/Neutrino:Einstel ... aktivieren

Gruß
Immer wieder einen Klick wert: Tuxbox-Wiki -- Tuxbox-Forum -- TuxFutter Wiki -- u-Grabber -- MovieGuider
Nach oben
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

#3 Beitrag von tklcb » So 06 Jan 2008, 16:20

Hallo,

danke erstmal für die schnelle Reaktion!

Es ist ein JtG 2.2 v. 21.12.2007 (2.2.6)

Die Box ist mit diesem Image neu geladen worden, da sie diesen Fehler auch schon mit einem andern Image gezeigt hatte, bei der Sendersuche bietet sie mir nur die Sat Suche an, keine Suche im Kabelnetz verfügbar.

AVIA Watchdog steht zur Zeit auf: ein

Danke im Voraus!
Nach oben
Benutzeravatar
Jeppdot
Streamsüchtling
Streamsüchtling
Beiträge: 1784
Registriert: Do 01 Jan 2004, 18:03
Kontaktdaten:
Kontaktdaten von Jeppdot

#4 Beitrag von Jeppdot » So 06 Jan 2008, 16:22

Ok das erklärt das:

Code: Alles auswählen

Code:
[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
Und was passiert beim 2ten Start?
Wenn die Einstellungen gespeichert sind?


Nachtrag:
wiki.tuxbox.org hat geschrieben: Hinweis:
Bei Boxen mit AViA500 (nur Nokia) kann es bei aktiviertem AViA-Watchdog zum Einfrieren des Systems kommen. Dies äußert sich durch folgende Symptome:

* Die betroffenen Boxen lassen sich nach einer unbestimmten Zeit (meist etwa >=12h) weder am Gerät noch über die Fernbedienung bedienen.
* Ausfall der Netzwerkfunktionalität
* Bild und Ton laufen jedoch weiter (Reset über Fronttasten kann ausgelöst werden)
* Sporadisch kommt es zu einem Kernel-Oops
* Images ohne komprimierte Partitionen (JFFS2-Only) (z.B. DietmarW) laufen deutlich länger
* Die Original-Betanova läuft auf der betroffenen DBox2 einwandfrei
Das hattest du aber gelesen?

Und noch ein Nachtrag:
avia_gt_ucode: loaded ucode vB107
warum das?


Gruß
Immer wieder einen Klick wert: Tuxbox-Wiki -- Tuxbox-Forum -- TuxFutter Wiki -- u-Grabber -- MovieGuider
Nach oben
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

#5 Beitrag von tklcb » So 06 Jan 2008, 16:38

...habe die Box jetzt nochmal booten lassen und mitgelogt; die Fehlermeldungen bleiben gleich...und sie will immer noch auf Astra suchen...

Liege ich mit meiner Vermutung richtig, das mit "Bus error" der I²C Bus gemeint ist?
Nach oben
Benutzeravatar
Jeppdot
Streamsüchtling
Streamsüchtling
Beiträge: 1784
Registriert: Do 01 Jan 2004, 18:03
Kontaktdaten:
Kontaktdaten von Jeppdot

#6 Beitrag von Jeppdot » So 06 Jan 2008, 16:42

Flash bitte mal ein ganz frisches Komplett-Image ohne was zurückzusichern. Und poste dann den Bootlog des ersten Starts.

Und dann den zweiten wo nur der Watchdog abgeschaltet ist.

Gruß
Immer wieder einen Klick wert: Tuxbox-Wiki -- Tuxbox-Forum -- TuxFutter Wiki -- u-Grabber -- MovieGuider
Nach oben
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

#7 Beitrag von tklcb » So 06 Jan 2008, 16:45

ok, wird gleich erledigt
Nach oben
Benutzeravatar
Jeppdot
Streamsüchtling
Streamsüchtling
Beiträge: 1784
Registriert: Do 01 Jan 2004, 18:03
Kontaktdaten:
Kontaktdaten von Jeppdot

#8 Beitrag von Jeppdot » So 06 Jan 2008, 16:49

Wenn das nix hilft dann ist wohl hier ein Beispielfür deinen Fehler :(

Aber du bist nicht alleine:
Tuxbox-Forum-Suche nach Oops: machine check, sig: 7


Gruß
Immer wieder einen Klick wert: Tuxbox-Wiki -- Tuxbox-Forum -- TuxFutter Wiki -- u-Grabber -- MovieGuider
Nach oben
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

#9 Beitrag von tklcb » So 06 Jan 2008, 17:00

...so, habe jetzt mit "Hallenberg" das JtG 2.2.6 frisch eingespielt, die Box resettet (auf dem Bildschirm habe ich die Meldung das die ucodes fehlen, ist ok, da ich ja bis jetzt nichts weiter eingespielt habe), das Log dazu hier (es fehlt wieder ein Stück vom Anfang, sollte es relevant sein, versuche ich noch einmal das Log komplett zu sichern)

"not tainted" würde ich mit "nicht fehlerfrei" übersetzen, ist das ok?

Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 694157 Bytes = 677.9 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.35.5-dbox2 (vom Jtg-Team) (gcc version 3.4.6) #1 Fr 21. Dez 0
9:53:57 CET 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x1000)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30780k available (1180k kernel code, 348k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1b:7d:5e
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x006a0000 : "root (SquashFS)"
0x006a0000-0x00800000 : "var (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.8.2 (2007-12-21 09:55:47 CET)
Starting the automounter
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
cam: no firmware file found
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av: AVIA500 sptsfix is off
Machine check in kernel mode.
Caused by (from SRR1=9032): Transfer error ack signal
Oops: machine check, sig: 7
NIP: C38F68D8 XER: 20000000 LR: C38F6B1C SP: C1B8BD90 REGS: c1b8bce0 TRAP: 0200
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c1b8a000[75] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C38F6B1C C1B8BD90 C1B8A000 00000080 00000000 C38FE000 C1CE6D0C FDFFE000
GPR08: C1CE6D20 C38FE000 00000000 00000000 48008024 10074260 10050000 00000001
GPR16: 10070000 10077868 1006FD79 10077520 00009032 C1B8BEA0 C1A34000 C3900000
GPR24: C1CE6CE0 00000007 C38FC000 C01465C4 FFFFFFEA 00000000 C0150000 C38F6000
Call backtrace:
C38F6B1C C38F8964 C00110D4 C000285C 100098E8 10003C68 10003C98
10003E58 0FEB15EC 00000000
Bus error
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
jtginfo $Id: jtginfo.c,v 1.9 2007/12/20 19:34:12 jtgriker Exp $
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Thu Jan 1 12:00:00 CET 1970
$Id: sectionsd.cpp,v 1.253 2007/12/02 14:46:36 seife Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/neutrino.conf for reading.
[sectionsd] /var/tuxbox/config/neutrino.conf not found
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Caching 6 hours Extended Text
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
$Id: zapit.cpp,v 1.404 2007/12/17 09:53:04 seife Exp $
[ConfigFile] Unable to open file /var/tuxbox/config/zapit/zapit.conf for reading
.
[frontend] uncommitted_switch_mode 0
/var/tuxbox/config/zapit/services.xml: No such file or directory
Machine check in kernel mode.
Caused by (from SRR1=1032): Transfer error ack signal
Oops: machine check, sig: 7
NIP: C38F6098 XER: 20000000 LR: C38F6088 SP: C1571E10 REGS: c1571d60 TRAP: 0200
Not tainted
MSR: 00001032 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c1570000[123] 'zapit' Last syscall: 54
last math 00000000 last altivec 00000000
GPR00: 00000000 C1571E10 C1570000 00000001 000000E0 20006F06 00000000 C3B8C9E8
GPR08: 0FD5E7F0 C38FE000 C3900000 C0004BE0 84002028 10037468 00000000 00000000
GPR16: 00000000 00000000 00000000 00000000 00009032 01571F40 C3B8C9E8 C18C56D0
GPR24: C15DBD00 00000001 00000000 00000000 000000E0 00000000 00000000 00000000
Call backtrace:
C003EDA4 C3B8CEC0 C38D24E8 C38CD380 C0043FEC C000285C 00000000
10014E58 10014F28 10010B04 10013190 0FC9B5EC 00000000
[camd] CA_SEND_MSG: No such device
[camd] CA_SEND_MSG: No such device
$Id: controld.cpp,v 1.127 2007/07/01 08:40:13 dbluelle Exp $

[ConfigFile] Unable to open file /var/tuxbox/config/controld.conf for reading.
[controld] /var/tuxbox/config/controld.conf not found
[controld] Boxtype detected: (1, Nokia D-BOX2)
Machine check in kernel mode.
Caused by (from SRR1=1032): Transfer error ack signal
Oops: machine check, sig: 7
NIP: C38F6098 XER: 00000000 LR: C38F6088 SP: C1539DB0 REGS: c1539d00 TRAP: 0200
Not tainted
MSR: 00001032 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c1538000[130] 'controld' Last syscall: 54
last math 00000000 last altivec 00000000
GPR00: 00000000 C1539DB0 C1538000 00000001 000003B0 C1539E14 C1539E50 C3B8C35C
GPR08: 00000000 C38FE000 C3900000 C0004BE0 84002028 1002122C 00000000 00000000
GPR16: 00000000 00000000 00000000 00000000 00009032 01539F40 C3B8C35C C18C5DD0
GPR24: C153B980 00000002 00000000 C1539E14 000003B0 00000000 7FFFFD00 C1539E50
Call backtrace:
00000000 C38F8750 C3B8C68C C38D25C8 C38CD380 C0043FEC C000285C
3000A6A8 10006480 10006C50 10005F50 0FC475EC 00000000
[yhttpd] Webserver nhttpd/3.1.6 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[ConfigFile] Unable to open file /var/tuxbox/config/nhttpd.conf for reading.
[yhttpd] Webserver starting...
/bin/neutrino: /lib/libpng12.so.0: no version information available (required by
/bin/neutrino)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[ConfigFile] Unable to open file /var/tuxbox/config/neutrino.conf for reading.
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[ConfigFile] Unable to open file /var/tuxbox/config/scan.conf for reading.
[neutrino] Loading of scan settings failed. Using defaults.
cannot read locale: No such file or directory
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
/dev/input/event1: No such file or directory
[neutrino] menue setup
loading locales: scandir: No such file or directory
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[neutrino] received 0 sats
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[neutrino] registering as event client
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/controld.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[CBasicClient] connect failed.
/tmp/zapit.sock: Connection refused
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[sectionsd] getUTC: read: Connection timed out
Nach oben
Benutzeravatar
Jeppdot
Streamsüchtling
Streamsüchtling
Beiträge: 1784
Registriert: Do 01 Jan 2004, 18:03
Kontaktdaten:
Kontaktdaten von Jeppdot

#10 Beitrag von Jeppdot » So 06 Jan 2008, 17:08

Das Hier sieht deiner Meldung

Code: Alles auswählen

Machine check in kernel mode.
Caused by (from SRR1=9032): Transfer error ack signal
Oops: machine check, sig: 7
NIP: C38F68D8 XER: 20000000 LR: C38F6B1C SP: C1B8BD90 REGS: c1b8bce0 TRAP: 0200
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
TASK = c1b8a000[75] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C38F6B1C C1B8BD90 C1B8A000 00000080 00000000 C38FE000 C1CE6D0C FDFFE000
GPR08: C1CE6D20 C38FE000 00000000 00000000 48008024 10074260 10050000 00000001
GPR16: 10070000 10077868 1006FD79 10077520 00009032 C1B8BEA0 C1A34000 C3900000
GPR24: C1CE6CE0 00000007 C38FC000 C01465C4 FFFFFFEA 00000000 C0150000 C38F6000
Call backtrace:
C38F6B1C C38F8964 C00110D4 C000285C 100098E8 10003C68 10003C98
10003E58 0FEB15EC 00000000
Bus error
leider verdammt ähnlich.

Also ich würde auf Hardware tippen. Poste das Log doch mal im TuxBox-Forum da sitzen die Hardware-Cracks.

Gruß
Immer wieder einen Klick wert: Tuxbox-Wiki -- Tuxbox-Forum -- TuxFutter Wiki -- u-Grabber -- MovieGuider
Nach oben
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

#11 Beitrag von tklcb » So 06 Jan 2008, 17:21

Danke Jeppdot, ...na da bin ich ja wenigstens nicht der einzige...


mal schauen, ob noch jemand eine Diagnose für die Box hat...
Nach oben
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

#12 Beitrag von tklcb » So 06 Jan 2008, 18:00

...mir ist gerade aufgefallen, das ich nicht dazu geschrieben hatte, das die Box mit einem AVIA-600L bestückt ist; der Link oben hat mich darauf gebracht, da war es allerdings eine SAGEM mit 1xI, vielleicht hilft das bei der Diagnose.

Danke.
Nach oben
Riker
TuxBox CDK Experte
TuxBox CDK Experte
Beiträge: 1466
Registriert: Mo 04 Aug 2003, 16:22
Wohnort: Hallenberg.com
Kontaktdaten:
Kontaktdaten von Riker

#13 Beitrag von Riker » So 06 Jan 2008, 20:33

Avia defekt ( Glaskugel )

Gruß Riker
1. Nokia Sat 2xI Avia 600 7-farbiges Display, IDE 120GB HDD 2,5"
2. Dreambox DM8000-HD an 46" Full-HD Samsung LED-TV
3. Diverese d-Boxen und Dreamboxen im Schrank
4. habe fertig
Nach oben
tklcb
Einmal-Streamer
Einmal-Streamer
Beiträge: 9
Registriert: So 06 Jan 2008, 15:35

#14 Beitrag von tklcb » So 06 Jan 2008, 20:42

Hallo Riker,

deiner Aussage entnehme ich, das sich nicht soviel genaues aus dem Log ablesen läßt?!

Ist meine Vermutung richtig, das die vielen Ziffernblöcke Speicheradressen sind, welche evtl. nicht richtig angesprochen werden, weil ebend defekt?

Ich habe mal die Box direkt per yweb angesprochen (Tools, Info), allerdings habe ich da jetzt keinen Vergleich zu einer funktionierenden gleichen Box, so das mir die diversen Angaben dort erstmal nicht weiterhelfen.
Nach oben
Antworten

Zurück zu „Rund um die dbox2- Third Party“