Stingray! hat geschrieben:Ein IDE->SATA Adapter der mit unseren Interface gestet wurde und funktioniert erhälst Du bei abel.tv
Anstatt einen weiteren IDE->SATA Adapter zu kaufen, hab ich mich entschieden gleich ein SATA-Interface zu bestellen und das IDE-Interface in meine zweite dbox einzubauen.
Das SATA-Interface wurde heute geliefert aber ich bekomme daran die IDE-Festplatte einfach nicht zum Laufen ->
hda: lost interrupt
Code: Alles auswählen
Harddisk Menu 2008-08-02 JTG-Riker V0.39
[neutrino ide] /proc/mounts missing or ide device mountpoint not found
[neutrino ide] Set mountpoint to default: /hdd
[sectionsd] getUTC: read: Connection timed out
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.13 2009/01/13 22:13:23 dbt Exp $
ide: late registration of driver.
dboxide: activating cs2
oxide: address space of IDE-Interface is at: 0xc3cc1000
dboxide: IDE-Interface detected, Vendor: DboxBaer or kpt.ahab/Stingray
dboxide: sreset succeeded
Probing IDE interface ide0...
hda: WDC WD2500BEVE-00WZT0, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
hda: attached ide-disk driver.
hda: host protected area => 1
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
hda: lost interrupt
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
[sectionsd] getUTC: read: Connection timed out
hda: lost interrupt
Partition check:
/dev/ide/host0/bus0/target0/lun0:[sectionsd] getUTC: read: Connection timed out
<3>hda: lost interrupt
p1 p2
SGI XFS with no debug enabled
Wenn ich aber das SATA-Interface ausbaue und mit den selben Kabeln (!) das IDE-Interface dranhänge funktioniert die HD einwandfrei.
Code: Alles auswählen
Harddisk Menu 2008-08-02 JTG-Riker V0.39
[neutrino ide] /proc/mounts missing or ide device mountpoint not found
[neutrino ide] Set mountpoint to default: /hdd
[sectionsd] getUTC: read: Connection timed out
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.13 2009/01/13 22:13:23 dbt Exp $
ide: late registration of driver.
dboxide: activating cs2
oxide: address space of IDE-Interface is at: 0xc3cc1000
dboxide: IDE-Interface detected, Vendor: DboxBaer or kpt.ahab/Stingray
dboxide: sreset succeeded
Probing IDE interface ide0...
hda: WDC WD2500BEVE-00WZT0, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2
SGI XFS with no debug enabled
Braucht man für das SATA-Interface andere Treiber?
Oder muss sonst etwas Bestimmtes eingestellt werden?
Das Kabel am Modemport sitzt auf jeden Fall richtig.